Evaluating volume reduction of clarified acid bovine milk whey via falling film vacuum evaporation
Carlos Jesús Muvdi-Nova, Said Andrey Mora-García, Sergio Alejandro Cáceres-Roa
Evaluating volume reduction of clarified acid bovine milk whey via falling film vacuum evaporation
Ciencia y Tecnología Agropecuaria, vol. 22, no. 1, 2021
Corporación Colombiana de Investigación Agropecuaria
Said Andrey Mora-García 
Universidad Industrial de Santander, Colombia
Sergio Alejandro Cáceres-Roa
Universidad Industrial de Santander, Colombia
Received: january 07, 2019
Accepted: august 03, 2020
Published: february 26, 2021
Funding
Funding source: Universidad Industrial de Santander
Contract number: VIE9364
Award recipient: Project VIE9364
Abstract: This research evaluates the effect of falling film vacuum evaporation on the characteristics of clarified acid bovine milk whey. The clarified acid whey was obtained by microfiltration (ceramic membranes, 0.2 µm cut-off, ∆TMP: 2 bar) and concentrated by a falling film evaporator. The clarified whey composition was mainly protein (0.32 ± 0.06 % w/w), ashes (0.56 ± 0.08 % w/w), soluble solids (5 ± 1 % w/w), and turbidity (16 ± 5 NTU). During the concentration step, the number of cycles changed notoriously for each volume reduction factor (VRF), being four the highest value achieved, with an average number of cycles of 18. The characteristics of concentrates were not affected by differences in the number of cycles, increasing proportionally with the VRF; it could be noticed in the final content that protein, ashes, and °Bx increased linearly around 3.5 times the initial composition. However, turbidity was different for each VRF because of heat treatment during the concentration stage (above 60 °C). A thermal treatment step after ricotta preparation would be advisable to remove the remaining protein. Tukey’s test was carried out at a 95 % CI, revealing statistical differences among means; therefore, there was a change in the characteristics of the final concentrated whey. Regarding color (absorbance), there were no considerable changes during the concentration process.
Keywords: acid whey, concentration, dairy industry, evaporation, falling film vacuum, volume reduction factor.
Resumen: Se evaluó el efecto de la evaporación de película descendente al vacío en las características de lactosueros ácidos previamente clarificados mediante microfiltración (membranas cerámicas, umbral de corte: 0,2 µm y ∆PTM: 2 bar). La composición del lactosuero inicial fue proteína 0,32 ± 0,06 % p/p, cenizas 0,56 ± 0,08 % p/p, sólidos solubles 5 ± 1 % p/p (°Bx) y turbidez 16 ± 5 NTU. Durante la etapa de concentración, el número de ciclos cambió de forma notoria para cada factor de reducción de volumen (FRV), cuyo valor máximo fue de 4 con un promedio de 18 ciclos por lote. Las características de los concentrados no se vieron afectadas por las diferencias en el número de ciclos, los cuales aumentaron en proporción al FRV. Esto pudo evidenciarse en la composición de proteína, cenizas y °Bx, que incrementaron su valor de forma lineal cerca de 3,5 veces más con respecto a la composición inicial. Sin embargo, la turbidez fue diferente debido al tratamiento térmico durante la etapa de concentración (por encima de 60 °C), por lo que es conveniente llevar a cabo una etapa de tratamiento térmico después de la elaboración del queso ricota para remover la proteína remanente. La prueba de Tukey con nivel de confianza del 95 % confirmó que hubo cambios en la composición del lactosuero final concentrado. No se evidenciaron cambios en el color (absorbancia) durante el proceso de concentración.
Palabras clave: concentración, evaporación, factor de reducción de volumen, industria lechera, lactosuero ácido, película descendente al vacío.
Introduction
One of the most obtained by-products in the dairy industry is whey (green-yellow liquid), which results from milk coagulation during cheese making. It represents between 85 and 90 % of milk volume and has more than 50 % of the milk nutrients (Almécija, 2007; Guerrero-Rodríguez et al., 2012). Acid whey is a type of whey obtained from acid milk coagulation (pH between 4.5 and 5.0) during the stretched-curd cheese production (Jelen, 2003). In Colombia, this type of cheese is widespread and makes part of the most produced in this country, therefore, its production is considerable (Vásquez, 2017).
According to Liu et al. (2005), 9 kg of whey are obtained per 1 kg of curd. Considering that ratio, and a Colombian cheese production of 50,000 tons (Escobar, 2015), whey production is nearly 440 million liters. However, this by-product is not completely valued and is intended mainly for animal feed. In many cases, it is released into soils and water sources due to a lack of awareness of how to take advantage of this raw material (Londoño et al., 2008), becoming a significant pollutant because of its organic matter content (fat, lactose, proteins, among others) (Ghaly & Kamal, 2004; Mukhopadhyay et al., 2005). In comparison with traditional whey, the acidity of this whey prevents the proliferation of microorganisms and favors its conservation (Simanca et al., 2010) and processing.
Falling film vacuum evaporation is a technique that can be used for the processing of dairy products. It allows reducing significant product volumes, concentrating high-value components, and removing as much water content as possible, without thermal degradation of the raw material due to vacuum conditions (reduced boiling point). With this technique, it is possible to treat heat-sensitive materials due to its high heat transfer coefficients (2000-4000 W/m2∙°C), thereby reducing thermal degradation of products, power consumption, and residence times, in comparison with traditional evaporation (Chen & Jebson, 1997; Li et al., 2011). This evaporation stage will improve and enhance the characteristics of this by-product, becoming a raw material for other processes to obtain high-quality finished products (Bimbenet et al., 2007; Zhu et al., 2011).
Pereira (2015) has used this technique to concentrate skimmed milk and acid whey at 200 mbar and 60 °C, achieving a volume reduction factor (VRF) of nearly 2 for both cases. Despite this, the studies reporting this process technique for acid whey concentration are few. Most studies have focused on heat transfer coefficient calculation and optimization for different industrial solutions, where milk is commonly the product of interest (Jebson & Iyer, 1991; Monnier et al., 2012). Arias and Espinel (2006) worked with traditional evaporation as an intermediate stage for whey concentration using stockpots. However, there is no detailed study of this technique’s effect on the concentrated product’s characteristics. More importantly, none of these studies analyzed the effect of a higher VRF on the product characteristics. Therefore, this study aims to evaluate the effect of falling film vacuum evaporation on the number of cycles and concentrate characteristics reaching a VRF of 4 in the batch configuration.
Material and methods
Raw material pretreatment
The acid whey used was clarified previously by membrane filtration. The clarification was performed with skimmed and deproteinized whey (at 100 °C, 15 min), pre-filtered with canvas. The filtration process was conducted using a 1.0 m-long membrane module, six mono-channel tubular ceramic membranes with a 0.2 µm membrane cut-off (TAMI® Industries, Nyons, France), a surface area of 0.132 m2 (six membranes), filtration conditions at 70 °C, and transmembrane pressure gradient (ΔTMP) of 2 bar. The physicochemical characteristics of the whey used in this study are shown in table 1.
Initial acid whey on a dry basis
Note.Mean absolute deviation.
Source: Elaborated by the authors
Falling film vacuum evaporation procedure
Five lots of acid whey were processed (19 L each lot). Muñoz and Solano (2014) designed and reported the evaporator used (figure 1), which consists of a 1.4 m-long stainless-steel tube (4) with a diameter of
3.8 cm and a 1.2 m-long, 3 mm-thick transparent acrylic tube with a diameter of 5 cm (figure 1). This evaporator has a heating system formed by two 1600 W resistors located inside the evaporator tube and connected to 220 V for a better temperature control system. The acid whey (4-5 °Bx) was fed by suction through a vacuum pump (working pressure of 200 mbar) (9) at temperatures between 60 and 65 °C. At the evaporator outlet, the concentrated whey was separated from water vapor streams and stored in different storage tanks (7, 8). Once a cycle was over, the concentrated whey was fed again to the feeding tank (3) to begin a new cycle. The process was finished upon achieving a VRF of 4.
Figure 1
Diagram of the falling film vacuum evaporator used in this study
Source: Muñoz and Solano (2014)
Quantification methods
Samples were characterized by dry matter % (Association of Official Analytical Communities International [AOAC International], 2006a); protein % (AOAC International, 2006b), ash % (AOAC International, 2005a), fat % (AOAC International, 2005b), calcium % (AOAC International, 2000a), phosphorus % (AOAC International, 2000b), lactic acid % (Association of Official Analytical Chemists, 1984), °Brix with Fisher No. 13 964 74C portable refractometer (0-90 °Bx) and turbidity with Hanna® HI 98703 turbidimeter. Samples were studied for color analysis through visible spectrophotometry at 440 nm, similar to Benavides-Prada and Muvdi-Nova (2014). HPLC was used for lactose % with a 7.8 x 300 mm COREGEL 107-H Column (8 µm) at 30 °C and 0.6 mL/min. The mobile phase was an aqueous solution of 8 mM H2SO4 using the isocratic mode. Tukey’s test was carried out to verify statistical differences among mean values obtained from the physicochemical analysis using Minitab statistical software, v. 19.
Results and discussion
The VRF achieved in this study was 4 (around 18 °Bx) due to a very stable foam, which stopped water removal from the whey solution. Nicorescu et al. (2009) attributed this phenomenon to the protein in treated whey, which has foaming properties that can be amplified by heat denaturation (Hui, 1993). The number of cycles used to achieve each VRF are shown in figure 2 —a cycle corresponds to one pass of the solution through the evaporator system—. It indicates that the number of cycles increases linearly with VRF. Tukey’s test confirms this linear behavior because the mean values among VRFs are different from each other. It was also challenging to keep falling film uniformity constant, which made the standard deviation of the number of cycles increased with the VRF.
Figure 2
The number of cycles used for each VRF in the concentration process at 60–65 °C and 200 mbar. SD: standard deviation
Note: Mean values that do not share the same letter are significantly different. Information was grouped using Tukey’s method and 95 % CI.
Source: Elaborated by the authors
°Bx, proteins, and ashes contents increased with the VRF (figure 3). It is noteworthy that they were not affected by the deviation in the number of cycles for each VRF.
Figure 3
°Bx, proteins, and ashes contents in concentrates obtained for each VRF at 200 mbar and 60- 65 °C. SD: standard deviation
Note: Mean values that do not share a letter are significantly different. Information was grouped using Tukey’s method and 95 % CI.
Source: Elaborated by the authors
Whey turbidity as a function of the VRF is shown in figure 4. All the samples were diluted to the initial concentration (4–5 °Bx; VRF = 1 as a baseline), to find variations in turbidity due to the concentration process.
Figure 4
Turbidity in whey concentrates for each VRF at 200 mbar and 60–65 °C. SD: standard deviation
Note: Mean values that do not share a letter are significantly different. Information was grouped using Tukey’s method and 95 % CI.
Source: Elaborated by the authors
These results show that turbidity increases with whey concentration —mean values are different from each other, according to Tukey’s test—, suggesting that part of the soluble serum protein became insoluble due to irreversible protein denaturation produced by heat treatment (above 60 °C) (Álvarez, 2013; Parris et al., 1991). Muñoz and Solano (2014) and Anaya and Bueno (2015) reported the results for cassava starch hydrolysate concentration using the same equipment, showing that their samples’ turbidity was not affected.
The effect of VRF on sample color was analyzed by absorbance at 440 nm, similar to Benavides-Prada and Muvdi-Nova (2014); at this wavelength, the transmitted or reflexed color is yellow (Harris, 2007). All the samples also were diluted to the initial value (VRF = 1 as a baseline). As whey is concentrated, absorbance increased slightly; after running an average of 18 cycles (figure 5). However, Tukey’s test shows that there is not a significant difference among mean values. Absorbance changes in the visible spectrum are related to color alteration and product thermal degradation (browning degradation).
Figure 5
The sample’s absorbance concentrates for each VRF at 200 mbar, 60–65 °C, and L=440 nm. SD: standard deviation
Note: Mean values that do not share a letter are significantly different. Information was grouped using Tukey’s test and 95 % CI.
Source: Elaborated by the authors
Benavides-Prada and Muvdi-Nova (2014) studied glucose syrups concentration using a rising film evaporator. They reported absorbance increased from 0.5 to 1.3 when running between 1 and 3 cycles, showing the low influence of falling film evaporation on whey color (associated with low browning degradation). One highlight of the obtained concentrates was the crystallization of some solids during storage at 4 °C. According to Luquet (1993), it is due to the formation of α-lactose monohydrate (crystals) at temperatures below 15 °C. This characteristic would facilitate further treatment stages, such as separation and drying.
Conclusions
The effect of falling film vacuum evaporation on acid whey permeate was analyzed, observing a linear behavior of the number of cycles regarding VRF, despite the difficulty for falling film formation. There was not browning degradation during the process, showing the low influence of this technique on the product. °Brix, protein, and ashes contents were not affected by the process and were directly proportional to the VRF. Turbidity changed considerably with the VRF due to the presence of insoluble denatured protein formed during the process; for this reason, it would be advisable to consider thermal treatment after ricotta preparation to remove the remaining protein. The use of anti-foaming agents is recommended to obtain a higher VRF.
Disclaimers
All authors made significant contributions to the document, agreed with its publication, and declare no conflicts of interest in this study.
Acknowledgments
The authors gratefully acknowledge Universidad Industrial de Santander for financing this research work through the project VIE9364 and the Servicio Nacional de Aprendizaje - SENA for supporting the supply of all the whey required in this research.
References
Almécija, M. C. (2007). Obtención de lactoferrina bovina mediante ultrafiltración de lactosuero [PhD thesis, Universidad de Granada]. Institutional repository UGR. http://hdl.handle.net/10481/1721
Álvarez, M. C. (2013). Caracterización fisicoquímica de los diferentes tipos de lactosueros producidos en la Cooperativa Colanta LTDA [Undergraduate thesis, Corporación Universitaria Lasallista]). Biblioteca Digital Lasallista. http://hdl.handle.net/10567/1036
Anaya, C., & Bueno, P. (2015). Simulación de la evaporación de película descendente al vacío y con gas de arrastre utilizando redes neuronales [Bachelor’s thesis, Universidad Industrial de Santander]. Repository UIS. http://tangara.uis.edu.co/biblioweb/tesis/2015/156223.pdf
Arias, M. J., & Espinel, A. O. (2006). Evaluación de la utilización de la microfiltración tangencial (MFT) para la fabricación de queso y aprovechamiento del lactosuero [Bachelor’s thesis, Escuela Politécnica Nacional]. Digital Repository EPN. https://bibdigital.epn.edu.ec/handle/15000/2724
Association of Official Analytical Communities International [AOAC International]. (2000a). Section 927.02. Calcium in animal feed. Dry ash method. In AOAC Official Methods of Analysis (17th ed.).
Association of Official Analytical Communities International [AOAC International]. (2000b). Section 965.17. Phosphorus in animal feed and pet food. Photometric method. In AOAC Official Methods of Analysis (17th ed.).
Association of Official Analytical Communities International [AOAC International]. (2005a). Section 923.03. Ash of flour. Direct method. In AOAC Official Methods of Analysis (18th ed.).
Association of Official Analytical Communities International [AOAC International]. (2005b). Section 2000.18. Fat content of raw and pasteurized whole milk. Gerber method. In AOAC Official Methods of Analysis (18th ed.).
Association of Official Analytical Communities International [AOAC International]. (2006a). Section 990.19 Solids (total) in milk by forced air oven drying after steam table pre-dry. In AOAC Official Methods of Analysis (18th ed.).
Association of Official Analytical Communities International [AOAC International]. (2006b). Section 991.20. Nitrogen (total) in milk. Kjeldahl methods. In AOAC Official Methods of Analysis (18th ed.).
Association of Official Analytical Chemists. (1984). Section 16.023. Titratable acidity. In AOAC Official Methods of Analysis (14th ed.).
Benavides-Prada, O. A., & Muvdi-Nova, C. J. (2014). Evaluación de la ósmosis inversa y de la evaporación de película ascendente como técnicas de concentración de hidrolizados de almidón de yuca. Revista ION, 27(1), 59-70. https://revistas.uis.edu.co/index.php/revistaion/article/view/4150
Bimbenet, J. J., Duquenoy, A., & Trystram, G. (2007). Génie des procédés alimentaires. Editorial DUNOD.
Chen, H., & Jebson, R. (1997). Factors affecting heat transfer in falling film evaporators. Food and Bioproducts Processing, 75(2), 111-116. https://doi.org/10.1205/096030897531423
Escobar, M. (2015, March). Fabricación de quesos como para récord Guiness. UN Periódico, 186. https://cienciasagrarias.medellin.unal.edu.co/index.php/46-news/noticiasfca/1076-fabricacion-de-quesos-como-para-record-guinness
Ghaly, A. E., & Kamal, M. A. (2004). Submerged yeast fermentation of acid cheese whey for protein production and pollution potential reduction. Water Research, 38(3), 631-644. https://doi.org/10.1016/j.watres.2003.10.019
Guerrero-Rodríguez, W., Castilla-Hernández, P., Cárdenas-Medina, K., Gómez-Aldapa, C., & Castro-Rosas, J. (2012). Degradación anaerobia de dos tipos de lactosuero en reactores UASB. Tecnología Química, 32(1), 99-106. https://tecnologiaquimica.uo.edu.cu/index.php/tq/article/view/720
Harris, D. (2007). Análisis químico cuantitativo. Editorial Reverté.
Hui, Y. (1993). Dairy Science and Technology Handbook. Volume 1. Principles and properties. Wiley.
Jebson, S., & Iyer, M. (1991). Performances of falling film evaporators. Journal of Dairy Research, 58(1), 29-38. https://doi.org/10.1017/S0022029900033483
Jelen, P. (2003). Whey processing. Utilization and Products. In H. Roginski, J. Fuquay, & P. Fox (Eds.), Encyclopedia of Dairy Sciences (pp. 2739-2745). Academic Press.
Li, W., Wu, X. Y., Luo, Z., & Webb, R. (2011). Falling water film evaporation on newly-designed enhanced tube bundle. International Journal of Heat and Mass Transfer, 54(13-14), 2990-2997. https://doi.org/10.1016/j.ijheatmasstransfer.2011.02.052
Liu, X., Chung, Y. K., Yang, S. T., & Yousef, A. (2005). Continuous nisin production in laboratory media and whey permeate by immobilized Lactococcus lactis. Process Biochemistry, 40(1), 13-24. https://doi.org/10.1016/j.procbio.2003.11.032
Londoño, M., Sepúlveda, J., Hernández, A., & Parra, J. (2008). Bebida fermentada de suero de queso fresco inoculada con Lactobacillus casei. Revista Facultad Nacional Agronomía Medellín, 61(1), 4409-4421. https://revistas.unal.edu.co/index.php/refame/article/view/24741
Luquet, M. (1993). Leche y productos lácteos: Transformación y tecnología. Editorial ACRIBIA.
Monnier, H., Portha, J. F., Kane, A., & Falk, L. (2012). Intensification of heat transfer during evaporation of a falling liquid film in vertical microchannels—Experimental investigations. Chemical Engineering Science, 75, 152-166. https://doi.org/10.1016/j.ces.2012.03.008
Mukhopadhyay, R., Chatterjee, S., Chatterjee, B. P., Banerjee, P., & Guha, A. K. (2005). Production of gluconic acid from whey by free and immobilized Aspergillus niger. International Dairy Journal, 15(3), 299-303. https://doi.org/10.1016/j.idairyj.2004.07.010
Muñoz, C., & Solano, R. (2014). Construcción e implementación de un piloto laboratorio de evaporación de película descendente. [Undergraduate thesis, Universidad Industrial de Santander]. Repository UIS. http://tangara.uis.edu.co/biblioweb/tesis/2014/152003.pdf
Nicorescu, I., Loisel, C., Riaublanc, A., Vial, C., Djelveh, G., Cuvelier, G., & Legrand, J. (2009). Effect of dynamic heat treatment on the physical properties of whey protein foams. Food Hydrocolloids, 23(4), 1209-1219. https://doi.org/10.1016/j.foodhyd.2008.09.005
Parris, N., Purcell, J., & Ptashkin, S. (1991) Thermal denaturation of whey proteins in skim milk. Journal of Agricultural and Food Science, 39(12), 2167-2170. https://doi.org/10.1021/jf00012a013
Pereira, A. C. (2015). Thermodynamic and hydrodynamic characterization of the vacuum evaporation process during concentration of dairy products in a falling evaporator [PhD thesis, Université Européenne de Bretagne]. HAL Archives Ouvertes. https://tel.archives-ouvertes.fr/tel-01342521/document
Simanca, M., Arteaga, M., Pérez, Y., Soto, M., & Salcedo, J. (2010). Caracterización y estudio de la fermentación espontánea del suero costeño producido en Montería. Revista MVZ Córdoba, 15(1), 1944-1953. https://doi.org/10.21897/rmvz.332
Vásquez, C. (2017, July 16). 12 son las clases de quesos que se elaboran en regiones de Colombia. ElMundo.com. https://www.elmundo.com/noticia/12-son-las-clases-de-quesos-que-se-elaboran-en-regiones-de-Colombia/355693
Zhu, P., Méjean, S., Blanchard, E., Jeantet, R., & Schuck, P. (2011). Prediction of dry mass glass transition temperature and the spray drying behavior of a concentrate using a desorption method. Journal of Food Engineering, 105(3), 460-467. https://doi.org/10.1016/j.jfoodeng.2011.03.003
Author notes
* Corresponding author: Universidad Industrial de Santander. Grupo CICTA. Sede UIS Guatiguará, km 2 vía el Refugio, Piedecuesta, Colombia. cjmuvdi@uis.edu.co
Additional information
Subject editor: Edwin Castro Rincón (Corporación Colombiana de Investigación Agropecuaria [AGROSAVIA])
How to cite this article: Muvdi-Nova, C. J., Mora-García, S. A., & Cáceres-Roa, S. A. (2021). Evaluating volume reduction of clarified acid bovine milk whey via falling film vacuum evaporation. Ciencia y Tecnología Agropecuaria, 22(1), e1241. https://doi.org/10.21930/rcta.vol22_num1_art:1241
Evaluating volume reduction of clarified acid bovine milk whey via falling film vacuum evaporation
issn: 0122-8706 - 2500-5308
DOI: 449964325010
Vol: 22
Numero: 1
Año: 2021
Corporación Colombiana de Investigación Agropecuaria
Said Andrey Mora-García
Universidad Industrial de Santander, Colombia
Sergio Alejandro Cáceres-Roa
Universidad Industrial de Santander, Colombia
